INDUcoder Messtechnik GmbH - INCREMENTAL DISPLAY MODULE MOD 13

INCREMENTAL DISPLAY MODULE MOD 13

Anzeigemodul mit programmierbaren Ausgängen für inkrementale Drehgeber

Module avec sortie programmer par Codeurs optiques incrémentaux

Display with programmable outputs for Incremental Encoder

MOD 13 - a programmable multifunctional display module for incremental encoders with output channel push-pull or RS422 line driver. Display parameters are fully programmable. MOD 13 has the usual standardfunction of a display modul, but additional two control outputs, which can be programmed separately as comparator, cam switch or pulse switch. Easy programming by four front-panel keys.

PRODUCT DESCRIPTION MOD 13:

Case

for panel mounting

Dimensions 111 x 144 x 72 mm

8-digit 7-segment red LED display, 14 mm high

Weight < 0,5 kg

Signal-Inputs

for operation of incremental encoders
Input-signals

•	6 channels AA + BB/90° + MM RS422 line driver or 3 channels A + B/90° +M with 5 V or 24 V voltage level
•	Input frequency up to 150 kHz
•	Optically insulated by optocoupler

Display-Parameter

•	Fully programmable
•	Scale factor
•	Decimal point
•	Zero offset

Cycle Time approx. 1 ms

1 Programmable control input

1 Control input for storage of
indicated value

2 Programmable Control-Outputs

•	Programmable separately as comparator, cam switch or pulse switch
•	Switching threshold adjustable for complete indicating range
•	Switching hysteresis adjustable
•	Optocoupler with NPN-Transistor, Open Emitter with PTC
•	Supply Voltage max. 35 VDC
•	Output current max. 50 mA
•	Output voltage min. supply voltage -2 V
•	Optically insulated by optocoupler

General Data

•	Supply Voltage 10 ... 35 VDC
•	Supply Voltage output 5 VDC, max. 350 mA
•	Power Consumption <150 mA (without load)
•	Operation temperature 0...50° Celsius

Protection

•	Front IP 50, with protective cover IP54, rear IP 20

Technical Data
Supply voltage	+10 ... 35 VDC
Power consumption	<150 mA (without load) at 24 VDC
Supply voltage output for incremental encoder	5 V max. 350 mA
Cycle time	1 ms
Display range	-9999999 ... 99999999
Display	8 digit 7-segment red LED, 14 mm high
Datamemory	EEPROM
Operating temperature	0 ... +50°C
Connections	Terminal block, max. 1,5 mm2
Weight	< 0,5 kg
Protection	front IP 50 with protective cover IP 54 rear IP 20
Signal-Inputs - Incremental Encoder
Number of input-signals	6 = AA + BB/90° + MM
Input-circuit	according to RS422
Input-voltage	max. 35 V
Input-Frequency	max. 150 kHz
Input-Resistance	3 kOhm at 24 V 350 Ohm at 5 V
pulse width Signal M	min. 2 µs
Control-Inputs
Circuit	Optocoupler
Input-Level Low	0 ... +5 VDC
Input-Level High	+10 ... 35 VDC
Input-Resistance	1,8 kOhm at 24 VDC
Control-Outputs
Circuit	Optocoupler NPN-Transistor, Open Emitter with PTC
Power supply	max. +35 VDC
Output-voltage	min. Vcc -3,5 V at 50 mA min. Vcc -2,0 V at 20 mA
Output-current	max. 50 mA, short circuit proof

Electrical connection diagram

(1)  Power supply for the output stages
(2)  0 V for the input stages
(3)  0 V for the signal inputs

Outline drawing

Connection of Incremental Encoder

Incremental Encoder with 6 channels
RS422 line driver outputs

Incremental Encoder with 3 channels
voltage level +5 V

Incremental Encoder with 3 channels
voltage level +10...35 V

INDUcoder Messtechnik GmbH, P.O. Box 18 03 49 47173 Duisburg, Germany	Phone:+49 203 57047-0, Fax:+49 203 57047-20 Email: aibncfdoe@fignhdiujckoldmenropdres
Technical changes to alteration. Publication of the shown data only with written authorization of INDUcoder Messtechnik GmbH.